# 1
Dear all,
I have some more information to narrow the problem. With lom> boot diag and then power on the system I got the message below. And after complete diagnostic of the system it just stopped and remains blinking. I tried #. key after that and could see lom prompt easily, while the system in running position. I executed the environment command while the system was in running condition and the output is below. I tried with command console and break and with both the command I got the cursor blinking, nothing more than that. I will be thankful for your valuable advice.
Best regards,
Bikash
lom>boot
bootmodenormal
lom>
lom>boot diag
lom>
lom>boot
bootmodediag
lom>
lom>poweron
lom>
[Host console]
LOM event: +0h17m8s host power on
Setting diag-switch? to true because of RSC command.
@(#)OBP 4.13.0 2004/01/19 18:27 Sun Fire 280R
Power-On Reset
Executing Power On SelfTest
0:0>
0:0>@(#) Sun Fire[TM] V280, Sun Blade[TM] 1000 POST 4.13.0 2004/03/15 19:13
/export/common-source/firmware_re/post/post-build-4.13.0/Camelot/excal/in
tegrated (firmware_re)
0:0>Copyright ?2004 Sun Microsystems, Inc. All rights reserved
SUN PROPRIETARY/CONFIDENTIAL.
Use is subject to license terms.
0:0>Jump from OBP->POST.
0:0>diag-switch? configuration variable set TRUE.
0:0>Diag level set to MIN.
0:0>Verbosity level set to 0.
0:0>MFG scrpt mode set to NONE
0:0>Done with First Init, reset system.
0:0>Current CPU frequency is 400 MHz.
0:0>Resetting to 750
0:0>Clock Synth Reset.
0:0>
0:0>Start selftest...
0:0>CPUs present in system: 0:0
0:0>Test CPU(s).....
0:0>Init CPU
0:0>UltraSparc_III_base Version 5.4
0:0>DMMU Registers Access
0:0>DMMU TLB DATA RAM Access
0:0>DMMU TLB TAGS Access
0:0>IMMU Registers Access
0:0>IMMU TLB DATA RAM Access
0:0>IMMU TLB TAGS Access
0:0>Probe Ecache
0:0>Size = 00000000.00800000...
0:0>Ecache Data Bitwalk
0:0>Ecache Address Bitwalk
0:0>Scrub and Setup Ecache
0:0>Setup and Enable DMMU
0:0>Setup DMMU Miss Handler
0:0>Test and Init Temp Mailbox
0:0>Init Scan/I2C.....
0:0>Initializing Scan Database
0:0>BBC:1483203b
0:0>SCSI:15060045
0:0>ICHIP:0d1e203b
0:0>RIO:13e5d03b
0:0>IO-Bridge:1824c06d
0:0>CPMS0:1142903b
0:0>CPMS1:1142903b
0:0>CPMS2:1142903b
0:0>CPMS3:1142903b
0:0>CPMS4:1142903b
0:0>CPMS5:1142903b
0:0>Init I2C
0:0>Unquiesce Safari
0:0>Blast Fans
0:0>Set Trip Temp CPU 0 to 110C
0:0>SUN JAN 21 8:39:39 GMT 7
0:0>Safari quick check
0:0> to IO-bridge_0
0:0>Safari full check
0:0> to IO-bridge_0
0:0>Basic Memory Test.....
0:0>Probe and Setup Memory
0:0>INFO:256MB Bank 0
0:0>INFO:No memory detected in Bank 1
0:0>INFO:256MB Bank 2
0:0>INFO:No memory detected in Bank 3
0:0>
0:0>Data Bitwalk on Master
0:0>Test Bank 0.
0:0>Test Bank 2.
0:0>Address Bitwalk on Master
0:0>
0:0>INFO: Addr walk mem test on CPU 0:0 Bank 0: 00000000.00000000 to 00000000.10
000000.
0:0>
0:0>INFO: Addr walk mem test on CPU 0:0 Bank 2: 00000002.00000000 to 00000002.10
000000.
0:0>Set Mailbox
0:0>Setup Final DMMU Entries
0:0>Post Image Region Scrub
0:0>Run POST from Memory
0:0>Verifying checksum on copied image.
0:0>The Memory's CHECKSUM value is 89c2.
0:0>The Memory's Content Size value is 9ad4c.
0:0>Success... Checksum on Memory Validated.
0:0>Memory Block.....
0:0>Print Mem Config
0:0>Caches : Icache is ON, Dcache is ON, Wcache is ON, Pcache is OFF.
0:0>Memory in non-interleave config:
0:0>Bank 0256MB : 00000000.00000000 -> 00000000.10000000.
0:0>Bank 2256MB : 00000002.00000000 -> 00000002.10000000.
0:0>Scrub Memory
0:0>Quick Block Mem Test
0:0>Quick Test 16777216 bytes at 00000000.00600000
0:0>40% Done...
0:0>Flush Caches
0:0>Get code in ecache.
0:0>IO-Bridge Tests.....
0:0>IO-Bridge unit 0 inittest
0:0>IO-Bridge unit 0 regtest
0:0>IO-Bridge unit 0 memtest
0:0>IO-Bridge unit 0 PCI DMA A test
0:0>IO-Bridge unit 0 PCI DMA B test
0:0>IO-Bridge unit 0 PCI merg test
0:0>IO-Bridge unit 0 PCI iommu test
0:0>IO-Bridge unit 0 PCI stctest
0:0>IO-Bridge unit 0 interrupt test
0:0>FPU Registers and Data Path
0:0>FPU Move Registers
0:0>FSR Read/Write
0:0>FPU BLOCK REG TEST
0:0>
0:0>Enable Errors.....
0:0>Turn IO-Bridge 0 errors on
0:0>Turn error traps on
0:0>INFO:
0:0>POST Passed all devices.
0:0>POST:Return to OBP.
0:0>Return to OBP, PASS
Setting diag-switch? to true because of RSC command.
@(#)OBP 4.13.0 2004/01/19 18:27 Sun Fire 280R
POST Results: Cpu 0
%o0 0000.0000.0000.0000
%o1 0000.0000.0000.0000
%o2 0000.0000.0000.0000
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.0010.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB (small-footprint mode) Done
MMUs ON
Find dropin, Copying Done, Size 0000.0000.0000.6f90
Jump to RAM Done
Find dropin, Copying Done, Size 0000.0000.0001.25d0
Setting diag-switch? to true because of RSC command.
@(#)OBP 4.13.0 2004/01/19 18:27 Sun Fire 280R
Loading Configuration
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.2000.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Block Scrubbing Done
Find dropin, Copying Done, Size 0000.0000.0000.6f90
Jump to RAM Done
Find dropin, (copied), Decompressing Done, Size 0000.0000.0006.2da0
ttya initialized
System Reset: (SPOR) (PLL)
Probing gptwo at 0,0 SUNW,UltraSPARC-III (750 MHz @ 5:1, 8 MB)
memory-controller
Probing gptwo at 1,0 Nothing there
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device
SUNW,fru-device
Loading onboard drivers: ebus flashprom i2c dimm-fru dimm-fru dimm-fru
dimm-fru bbc power i2c cpu-fru temperature fan-control
motherboard-fru ioexp ioexp fcal-backplane scc-reader power-supply
lomlite2 fan-control ioexp ioexp nvram idprom beep rtc gpio pmc
parallel SUNW,lombus lom-console serial SUNW,lomv
The cursor stayed blinking
#.
lom>environment
LEDs:
1 PowerON
2 FaultOFF
3 Supply A OFF
4 Supply B OFF
5 PSU okON
6 PSU fail OFF
Alarms:
1 -OFF
2 -OFF
3 -ON
PSUs:
1 ACOK
Fans:
1 PSU1 OK speed 78%
2 PSU2 OK speed 77%
3 CPU OK speed 76%
Temperature sensors:
1 Ambient OK 26degC
2 CPU0 enclosureOK 27degC
3 CPU0 die OK 62degC
4 CPU1 enclosurenot present
5 CPU1 die not present
Overheat sensors:
1 PSU OK
Circuit breakers:
1 SCC OK
2 PSU OK
lom>console
Blinking with no display
#.
lom>break
Still Blinking with no display
