and can you please explain to me this : rmclomv CPU_FAN @ MB.p1.f1.rs has failed

do I have configured a v890 with metadevices, one metadevice ie /dev/md/dsk/d6, sending messages of "out of inodes", can I work directly with the metadevice to assign more #of inodes or should I assign the inodes separately to the disks that conform the metadevice?I wait they can help me.Thank ...

Hi All,we've got an E450 server which crashed yesterday with the following messages:///////////////WARNING: [AFT1] Uncorrectable Memory Error on CPU3 Data access at TL=0, errID 0x 000405b6.816c859eAFSR 0x00000000.80200000 AFAR 0x00000000.7649f528AFSR.PSYND 0x0000(Score 05) AFSR.ETS 0x00 ...

Hi Everybody,I am getting the below Warning message frequently with my system, what might be problem behind this."Apr 6 10:50:57 hostname scsi: [ID 107833 kern.warning] WARNING: /pci@8,700000/scsi@2 (mpt0):"Regards,Bikash

Hi,The server unexpectedly switched off yesterday morning.The only one log line I found, by picld, saidWARNING: Device PS0 failure detected by sensor PS0_FAULT_SENSOR.The system is a SunFire 280R and has two power supplies. When I reached it, some 18 hours later, the general fault amber led was ...

Hello,I recently got in an X2100 M2 and am having problems getting an OS on it. I can't get the server to see the hard drives at all. They don't show up in BIOS and when I try to load RHEL 4 ES Update 4, it doesn't see any drives to install the OS on. I also tried using Fedora Core 6 and it ...

Hi everyone,I am just wondering if it is possible to set up a hardware Raid 10 on a Fire V445. As far as I read the documentation the answer is no! Although it is mentioned under "Highlights" in the server's data sheet where it says: "Hardware-RAID 0, 1 und 10"Using the SAS Controller for ...

Can anyone point me at a list of current Sun servers that support hardware based RAID?

Greetings,I have an SunFire 280R running solaris 10 update 11/06, to this system is attached an eonstor disk array (24 * 750 GB ) disk drives, but when booting the system i get the error "disk capacity is too large for current cdb length" which shocks as i would expect that a modern operating ...

Trying to setup hardware raid on a v250 and having no success. Wondering if I'm mistaken in believing that it has the ability!raidctl just returns "disks must be different" on creation attempts. And yes, the disks ARE different :-)

I just bought a Sun Netra T1 AC2000, however the system asks for a "firmware password".How would I reset it?I tried fooling around with jumpers, jp13/jp14 with no success.Where is the password stored? in NVRAM or in the System Configuration Card?

Does Sun still provide hardware support for the E4500?

Can older V240s 1.28Ghz/OBP 4.13.2 or 1.05Ghz OBP 4.11.4 use PC2700 memory? Recently upgraded newer V240 1.35GHZ/OBP 4.16.2 w/out a problem.

Any way to use the serial number to roughly calculate the manufacture date of a given server?

Hi,I just got my hands on an old Netra X1 and am planning on setting it up with Linux as a home server. I've had a little experience with Sun kit in the past and remember there were a few issues with disk size limitations.My question is - If I were to by a reasonibly big disk (between 250Gb ...

The service (yellow) LED on a new V440 is cycling on and off, mostly on, but there are no faults visible in prtdiag and the syslog is clean. Could this be caused by a non-conforming or 3rd party DIMM configuration? (We bought the system from a VAR who had a track record of picking junk off the ...

I'm looking to buy a V215 server with the following configuration but I have concerns about the PCI slots. I don't know if I have enough of the correct type (I'm unsure about backwards compatibility etc.) Can someone advise me on whether this configuration would work?The V215 has the ...

Hello all,I would like to upgrade the OS on an old 420R running Solaris 7 11/99 using a network installation server I set up. I need to boot it as a DHCP client to install a new OS over the network. When I tried to "boot net:dhcp - nowin" as I have with other servers, it does not boot and ...

Hello,I am having quite some DDSPE errors (up to 50 per day) on several SunV210/240 systems running Solaris 9:SUNW,UltraSPARC-IIIi: [ID 329692 kern.info] NOTICE: [AFT0] DDSPE Event on CPU0 in User mode at TL=0, errID 0x0006f281.edfa67d2Fault_PC 0xff1c7108SUNW,UltraSPARC-IIIi: [ID 662133 ...

We have a T1000 that wont start using it ALOM. We get the following error:SC Alert: SC Request to Power Off Host Immediately.We have tried starting in Maint and debug mode. With the same results. We can't get to the Ok prompt to try a network boot.Has anyone got any suggestions? Do you need ...

Hello,Anybody has any idea how can i switch from ALOM to system console.when i do break then sc> breakBreak can't happen due to the system power is off.sc> consoleEnter #. to return to ALOM.sc> poweronthen system boots up to the operating system then i try to do the following# ...

HII have 2 v890s in a cluster, but they have different OBP firmware levels:System PROM revisions:-OBP 4.22.19 2006/09/06 23:49System PROM revisions:-OBP 4.18.8 2006/01/19 11:19I've wasted a good half-hour of my life on the Sun site looking for the download are - can anyone direct me to it pls? ...

Hello from Switzerland.I'm not only pretty new to this forum but also to Sun, Cobalt, Solaris and all this stuff. Before getting to topics I would like to mention that I'm no native speaker, a heavy Apple and NeXT user who is not very familiar with UNIX, LINUX and all this. So please excuse ...

If I could install an RSC card in a SB 2000, would it think it is a SF 280R? They share the same systemboard.

Hello, we are using Sun Fire X2100 M2 with dual-core Opteron processor. I have two simple questions:Two applications are running parallel and want access memory at the same time (different memory cells). Does architecture support this simultaneous operation or access to memory is sequential. I ...

hello, I just start to using x4100 servers.and I have a question about this hardware.Once I put on two AC cables to servers, than servers will power onautomatically.so I wondering that how to setup this servers to power on by power button.Do I need to change some parameters at BIOS ...

I would like to purchase a sun server for development/hosting demos at work. We don't have a dedicated machine room. I tried a T1000 on a try and buy and it was an excellent machine but incredibly noisy. I need a machine that can run multiple simultaneous threads so as a minimum I require 2 * ...

We recently upgraded our ALOM to 1.6 on a V240 machine so we could utilize support of ssh.Since the upgrade, when configured to ssh, it hangs periodically. I don't know the frequency, other than to say I've been resetting it almost every day.I set it back to telnet and it does not hang.Has ...

Will that work?The quad core chips will have the same pin count and are Socket F. Will the M2 servers support the quad core chips, when they come out?

Can someone tell me how to update the Sun V20 BIOS, I have windows 2003 server installed.

I'm really interested in purchasing a Sun Fire x2200 but Sun sales support has not been responding to my email and IM requests for information about the base configuration. Here's my question: Does the base config (Config 1-M2) contain drive trays to install my own hard drives or are the bays ...

In the last 6 months I've had 4 hard disks fail in these servers and at no time has there been either anything in the SP, the only time it's been noticed that there's a disk failure is when I reboot the box with a console attached to it.They have all been Fujitsu MAY2073RC'sIs anyone else ...

Can the OBP on Sun Fire V240 be updated? If so how?

I wish to upgrade/expand the memory in my 420R from 2Gb to 4Gb. I have a complete set of memory totaling 4Gb from another 420R with boot issues (to be resolved later). I remove all memory fro the ailing 420R, set aside, then remove original 2Gb from 420R and replaced with the 4Gb of memory. ...

Hi AllWe have a Sun Fire V40z remote console configured.I am able to see the console till i get the login screen of the OS. Once i get the login screen of the OS, console gets hung.Any body please let me know what is the problemThanks in advance Kanki

Can I have only one OS e many servers modules? I would like to know if is possible que a set of server module can configured to work as a only one machine - and only onde OS (and which OS? Solaris and RedHat?)

I am trying to install solaris 10, but when I put the cd in the cdrom and issue the command boot cdrom -text I get the following error"Boot device: /pci@le,600000/ide@d/cdrom@0,0f File and args -text"Can't open boot device.Is this becuase the machine which is a V240 does not have the cdrom ...

I have a new server V490. I am trying to setup the SC card with permanent IP address.I plugged laptop directly into SC card and requires a password and login.I have been unable to login not knowing what the default password is, assuming this is what is required because this is a brand new ...

I set the profile up to c5t0d0 and it just dumps me out to terminal saying it can't find any disks...format command doesn't see them either. I am using sol 10x86 u2 miniroot for jump...any ideas?Message was edited by: dougtheman

Solaris 10 OS Hardware Compatibility List doesn't have Sun Fire V125 blade in its list. I wonder if they just forgot to add it there or it is not going to work with Solaris 10.ThanksMichael

The monitor on the dummy terminal connected to my Sun Fire V240 just died. I want to login using a laptop connected to the serial port on the back of the V240. I am connecting using Hyperterm (on the laptop) and connecting with a null-modem cable.The settings that I'm using for the ...

hello all,on T2000, disk 0 and disk 1 are mirrored:# raidctl -lRAIDVolume RAIDRAIDDiskVolume TypeStatus DiskStatusc0t0d0 IMOK c0t0d0 OKc0t1d0 OKNow, i want to break the mirror, and the idea is to mount the second disk on other T2000, then re-create the mirror. So i did the following steps:- ...

Hello,I have some questions about memory management in Sun Fire 6800 server with UltraSPARC-III Cu processors. Suppose I have a system with 16 processors and each board has 2GB memory. So the system totally has 8GB. I want to know if I run a parallel program, after the 64-bit virtual address ...

I have this new X2100 M2. I have a RAID 1 setup with two disks. When I boot from the RHEL 4 ES Update 4 (32 bit) install CD, it hangs when loading /sbin/loader.If I specify "linux noapic" it does the same thing. If I specify "linux noprobe" it goes into the install menu but the keyboard ...

We have a SparcStation2 running SunOS 4.1.3, recently had CPU board replaced and since then have had problems. We are able to ping it but not telnet to it. It reported a filesystem inconsistency on /usr, we fsck'ed it and it repaired several faulty superblocks and were able to shutdown and ...

Does anyone know how to get a v60 to perform a "network boot" via the LOM facility? The only way I can get a remote machine to network boot (in order to kickstart the machine) is to power cycle via the LOM, re-direct the console over the lan and try and insert an "F12" down the pipe during the ...

There is an old SUN Enterprise 250 box just sitting in the corner of our network laboratory and no key to turn the lock. I was just wondering if I had to go to all the trouble of taking the system apart or if there was an easier way to pick the key module. This thing has been sitting around and ...

I'm trying to add a new SDLT600 to an E4500 server. I do a reset-all, then when I run probe-scsi-all, the system hangs. I have 2 SBUS adapters, each with an A1000 attached, and the new tape is on one of these boards. I get this far:/sbus@7,0/SUNW,fas@3,8800000Target 0 Unit 0 Disk ...

Sun Fire V215 machine. The problem is that it does not automatically boot up to Solaris after a power outage. I have referred to ALOM configuration manual at: http://www.sun.com/products-n-solutions/hardware/docs/Servers/Workgroup_Servers /v215/index.htmlSC variable: sc_powerstatememory is set ...

Hello all,I would like to look into updating my Boot Prom to whatever version is now current for the Enterprise 420R system. Currently, my system reports the following in response to the .version command:Release 3.31 Version 0 created 2001/07/25 20:35OBP 3.31.0 2001/07/25 20:35POST 1.2.8 ...